DMC-16 / DMC+
The Dragonframe Master Controller is our flagship motion control coordinator. It comes in two varieties: The DMC-16 and the DMC+. The DMC-16 has 16 channels of step and direction that you can wire to your stepper motor drivers. The DMC+ provides powered drivers for channels 1-8, and step/dir signals for channels 9-16.
Use the DMC-16 with your own stepper motors drivers.
Use the DMC+ with your own stepper motors (or drivers for channels 9-16).
Arduino is an inexpensive, open-source hobby computer. We provide a special program (“Sketch” in Arduino world) called “DFMoco”. It provides 4-8 channels of step and direction output (depending on the Arduino model). We provide this sketch as a convenience, for people who are comfortable working with electronics and are interested in creating a homemade, low cost, simple motion control solution. We do not offer customizations of the DFMoco sketch (although you are free to do it yourself).
The DFMoco sketch is installed with Dragonframe at:
[Dragonframe Install folder]/Resources/Arc Motion Control/DFMoco
WIRING THE ARDUINO FOR MOTION CONTROL
An Arduino running the DFMoco sketch will generate step and direction signals for stepper motors.
If you already have stepper motor drivers, you can take these signals and wire them into a connector for those drivers.
If you do not have stepper motor drivers, and need to move relatively small stepper motors, you can wire the Arduino signals to a Big Easy Driver or comparable board. You will use one Big Easy Driver for each stepper motor.
The pin-out for each step and direction signal is described in the DFMoco sketch.
The eMotimo spectrum ST4 is a full-featured 4-axis controller with integrated pan and tilt control.
Additionally it has two powered motor output typically paired with a slider and focus motors.
It is accurate, repeatable, and supports cameras weighing up to 15lbs.
The eMotimo is the only third-party motion control equipment that implements our real-time protocol. This makes it faster for programming moves, performing tests, and even capturing real-time video.
Inquire at eMotimo.
SLIDEKAMERA produces high-quality motion control equipment for filmmakers, from lightweight DSLR’s to professional, heavy cinema cameras: sliders, remote heads with lens control, turntables and many more.
Using the new SLIDELINK PRO adapter enables real-time playback for SLIDEKAMERA hardware.
You can use it to shoot not only stop-motion animation but also live video: advanced packshots, VFX plates, greenscreens or feature film’s shots demanding advanced camera movement.
Inquire at Slidekamera.
edelkrone’s best-selling featured-packed SliderPLUS, Slide Module, and HeadPLUS motion control system is now compatible with Dragonframe software. When you connect HeadPLUS to your computer with edelkrone Stop Motion Module, you can control it through any PC or Mac. Stop Motion Module can also adjust the focus with the knob located on it, giving you ultra-precise and real-time feedback.
Inquire at edelkrone.
The edelkrone Stop Motion Module is non real-time (shoot-move-shoot only) when used with Dragonframe.
Noxon’s compact slider is light, rugged, and a very good value.
You can see it in action here: YouTube: Affordable 3 axis slider for video, timelapse and stopmotion.
Inquire at Noxon.
The Noxon Compact Slider + Dragonframe Adapter is non real-time (shoot-move-shoot only) when used with Dragonframe.
Note: You must select ‘DFMoco Arduino’ as the device type in Scene | Connections.
DitoGear produces motion control sliders, pan/tilt heads, and focus motors that are compatible with Dragonframe.
The DitoGear OmniSlider, OmniHead and LensDrive can be used with Dragonframe when paired with either the DitoGear DragonBridge or the DMC-16 motion controller.
For non real-time shooting, choose the DitoGear DragonBridge. This runs the DFMoco program to provide shoot-move-shoot capabilities, and is a great low cost option.
For real-time shooting, you must use the DMC-16 along with DitoGear DMC-16 adapters.
Inquire at DitoGear.
Dynamic Perception produces rugged, light-weight linear sliders and pan/tilt heads.
Their NMX Digital Motion Controller (3-axis stepper controller) is now Dragonframe compatible.
The NMX Digital Motion Controller is non real-time (shoot-move-shoot only) when used with Dragonframe.
Inquire at Dynamic Perception.
SmartSystem is an Italian-based company that creates high-precision linear sliders. Their SmartSlider Reflex S employs a unique fluid drag system to reduce vibration.
The DigiDRIVE Portable is a Dragonframe compatible controller. It can control all of the DigiDRIVE hardware.
The DigiDRIVE Portable is non real-time (shoot-move-shoot only) when used with Dragonframe.
Inquire at SmartSystem.